The gear in The Wyrm and the Maiden Grim

By Arttu Peltoniemi

Helmet

The nasal was updated before the film, but for some reason this is the only photo we have of the helmet. Nasal helmets have not been found in Scandinavia but were depicted in numerous period artwork. They were popular at the end of the 10th century.

Mail

The short sleeved mail shirt was worn by Roman soldiers already in the 3rd century. Since then the model spread all around Europe. Mail is the only known armour type used by Vikings. The reproduction Arttu wears in the film is made in India and has relatively large rings. Most historical mail had quite small rings because it offers more protection. There is one nearly complete Viking age mail shirt found in Gjermundbu, Norway.Shield

The shield we used is not a precise copy of any particular shield, but follows the overall standards of round center grip shield of the time. It’s 80 cm wide, 6 mm thick, and the boss is around 1 mm thick. For this movie we made the shield from plywood, but original shields were made of planks (and not out of any planks but split wood planks that are a bit different than your local hardware stores ones). Shields also get thinner towards the edges. At the very edge the shield is about 3mm thick. Shields were most likely covered with hide. Linen covering is hypothetical at best. Joeli painted the wyrm in this shield modeling Viking age art, but adding a smile for the wyrm as an original twist. The important point about plank shields is that sharp weapons cut into them much easier than they cut into plywood. We compensated these differences in the choreography with skill and knowledge.

Small spearhead (and butt piece)


As said in the original blog post the butt piece was a mistake. The earliest found counter weight in spears in Scandinavia is from 12th century. Leaf shaped heads seem to go out of fashion by 950 CE, but it is also suggested that a few leaf shaped heads may have continued in use throughout the Viking age.
         

Balancing spears can also be done by shaping the shaft thinning towards the spearhead. This is considerably more affordable method for men of the 10th century. The drawback is that designing the spear so that the counterweight works, reduces one’s ability to throw it. There are mentions in the sagas of men fighting with spear and shield, which seems to be the predominant way of fighting in the Viking age. It doesn’t seem unreasonable to think you would make a spear shaft for that purpose.


Large spearhead

           

The spearhead Joeli is using is close to Jan Petersen’s type F, dating it to 825–950 CE. 

We attached it to a long ash shaft and we see it as a cutting tool as well as a tool to thrust. With a heavy ash pole it is also a bone breaker if not like a quarterstaff, but good enough. Both shafts we use for spears in this movie are purely hypothetical. The only ever found shaft for a viking age spear is in the picture above.


Seax


A local multi-tool of iron age design as found around the shores of the Gulf of Finland. 35 cm, 320 g. Joeli made the handle roughly according to a 1200-year old bronze example. This time from ash, walnut, hide, beeswax and iron pigment.

 The handle is super nice to use. It’s again hypothetical to put this handle in this blade, but so would be any other handle. 

 We thought to arm the traveling soldier with a blade that is as much of a tool than it is a weapon, since a traveler would need one. 


Image credits:

https://secretsoftheice.com/news/2017/11/29/spear/

http://sagy.vikingove.cz/scandinavian-helmets-of-the-10th-century/#middle

http://www.vikingage.org/wiki/wiki/Spears

http://warfare.gq/6C-11C/Exultet_beneventano-Lombards-10C.htm?i=1
http://www.angelfire.com/wy/svenskildbiter/armsandarmour/mailshrt.html

The original shield pictured here is currently in the historic museum of Oslo. Mail has that same adres.

Comments

Post a Comment

Most popular posts:

Making our first viking age shield

By Arttu Peltoniemi
Image
The preparation of our first shield was a long process. It took a lot of studying and this is a version Arttu was most interested in building. The preference was to make as light and agile a shield as possible. It is made of radially cut spruce. The boss is made of gnarl, the handle is ash, and the raw hide is deer. The planks are 6 mm thick in the middle of the shield and about 3 mm thick on the edge. The board Radially cut planks were a huge problem and we made some ourselves, but those turned out just a bit too thin and ended up becoming scabbards instead. We managed to buy radially cut planks from Fiskarssin saha . These enabled Arttu to make the board. Originally tried from pine                                Self made planks came 3-5 mm thick :(        From Fiskarssin saha (Finnish company) After using a circular saw Then there was some simple gluing with hide glue. Clamps.... ...an...
Read more

Testing thin and thick shields against Viking Age weapons

By Arttu Peltoniemi
Image
We have build two shield with similar construction. Both are made just like the one we named Fat little sister , with the exception that the other ( Skinny brother ) is made of 6 mm thick planks and the fat one is made out of 10 mm thick planks. Read about the construction of the Fat little sister from this blog post: https://hirdmenn.blogspot.com/2022/01/fat-little-sister-making-of-sturdy.html The black paint is on the 6 mm thick shield and the white paint on the 10 mm thick shield.    Both are of spruce tree from the same order, so probably of the same age, maybe even from the same tree. The glueing was done the same way for both boards using same hide glue. Both have tanned leather facings from the same manufacturer. Both have raw hide edging from the same leather. The only difference is that the skinny one is painted with black iron oxide paint and the fat one has white chalk paint on it. Both are thinned down to 3 mm thickness on the edge, but the skinny one is shaved fr...
Read more

UNDERSTANDING THE SPEAR (and the overarm grip).

By Arttu Peltoniemi
Image
  It's been 12 years of training with a one handed spear for me (Arttu). Mostly I have trained weekly in summer time, but few years around the year. I started, and still continue, training with soft headed weapons in Finnish boffering scene. Also trained two handed pole weapons in HEMA context and one handed spear in Finnish reenactment scene. It took me 10 years before I became comfortable using a spear in the grip that is known as the overarm grip.    Underarm grip (left) and overarm grip Bef ore this I became ok with using the underarm grip. Here is a video of an accuracy drill. During my 10 year training I learned the sliding strike and to hold a long spear from the end of the shaft. I did not become comfortable in the overarm grip before I trained to throw the spear. (Here is an old, worst quality, training montage video .) There is a forever ongoing discussion about the grips that goes on in the armchair generals discussions of one handed spear fighting. To me the...
Read more